Ah, lol danke 🙂 Hatte bloß ein GUI Tool dafür gefunden.
Das spuckt er aus, habe mal beide Befehle ausgeführt, die ich bei dir gefunden habe:
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
bash-3.2# smartctl -a /dev/sda
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 5K80 family
Device Model: HTS548040M9AT00
Serial Number: MRL202L2GR3Y9G
Firmware Version: MG2OA5DA
User Capacity: 35,891,174,912 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Fri Jan 23 16:17:38 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 30) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 107 107 040 Pre-fail Offline - 4475
3 Spin_Up_Time 0x0007 214 214 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 725
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 132 132 040 Pre-fail Offline - 34
9 Power_On_Hours 0x0012 098 098 000 Old_age Always - 1022
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 528
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 11
193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 22719
194 Temperature_Celsius 0x0002 196 196 000 Old_age Always - 28 (Lifetime Min/Max 3/45)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 3
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 3 occurred at disk power-on lifetime: 5 hours (0 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 ff 52 a8 e4
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
f9 00 01 ff 52 a8 e4 00 00:01:54.800 SET MAX ADDRESS [OBS-6]
f8 00 00 00 00 00 e0 00 00:01:54.800 READ NATIVE MAX ADDRESS
f8 00 00 00 00 00 e0 00 00:01:54.800 READ NATIVE MAX ADDRESS
f8 00 00 00 00 00 e0 00 00:01:54.800 READ NATIVE MAX ADDRESS
20 00 01 ff 52 a8 e4 02 00:01:54.800 READ SECTOR(S)
Error 2 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 59 01 0f 8e a8 e4 Error: IDNF at LBA = 0x04a88e0f = 78155279
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
20 ff 01 0f 8e a8 e4 00 00:03:21.400 READ SECTOR(S)
c8 ff 01 0f 8e a8 e4 00 00:03:21.400 READ DMA
c8 ff 01 00 00 00 e0 00 00:03:21.000 READ DMA
ec 00 00 00 00 00 e0 00 00:03:08.600 IDENTIFY DEVICE
a1 00 00 00 00 00 e0 00 00:03:08.600 IDENTIFY PACKET DEVICE
Error 1 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 01 0f 8e a8 e4 Error: IDNF 1 sectors at LBA = 0x04a88e0f = 78155279
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 0f 8e a8 e4 00 00:03:21.400 READ DMA
c8 ff 01 00 00 00 e0 00 00:03:21.000 READ DMA
ec 00 00 00 00 00 e0 00 00:03:08.600 IDENTIFY DEVICE
a1 00 00 00 00 00 e0 00 00:03:08.600 IDENTIFY PACKET DEVICE
30 00 01 ff 52 a8 e4 02 00:01:57.400 WRITE SECTOR(S)
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Mir persönlich sagt das nun nix, aber es treten zumindest Fehler auf.
Die letzten 3 Mal (nach dem Systemupdate) konnte er allerdings erfolgreich booten. Allerdings das ja nichts heißen und es muss ja auch nicht zwingend heißen, dass die Platte noch in einem guten Zustand ist.
Bzgl. wLAN. Die Lampe dafür leuchtet nun endlich, aber er zeigt folgendes an:
bash-3.2# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 unassociated ESSID:off/any Nickname:"ipw2100"
Mode:Managed Channel=0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power:16 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
irda0 no wireless extensions.
eth1 ist - vermute ich mal, wLAN, aber irgendwie klingt das alles nicht danach (ipw2100 sagt mir nämlich was, sollte der Treiber oder der Chip vom wLAN sein)
Edit 2: Ok, habe KNetworkmanager doch endlich im AUR gefunden. Ich PEBCAK -.- :lol:
Ist das überhaupt das Standardprogramm für KDE und wLAN? Nicht, dass ich jetzt hier alles "kompliziert" über das AUR installiere und sich dann herausstellt, es ginge auch einfacher mit einem anderen Tool über Pacman :lol: