Hallo,
ich habe gestern ein Update gefahren.
Jetzt kommt beim hochfahren immer die Meldung: "eth0 timed out". Natürlich funktioniert deshalb mein Internet nicht mehr 🙁
Ich habe ein ASUS A8V Deluxe im Einsatz. Das hat ja bekanntlich den Marvell Chipsatz. Der hat auch bis dato immer funktioniert.
Hier mal meine rc.conf, obwohl ich daran nix geändert habe. Aber da ich nach dem Update neu gestartet habe, viel mir auf das in der rc.conf das Modul sk98lin nicht mehr drin stand. Ich hab es dann neu eingetragen, aber nix.....
#
# /etc/rc.conf - Main Configuration for Arch Linux
#
#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/unimaps
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE=de_DE@euro
HARDWARECLOCK="localtime"
TIMEZONE=Europe/Berlin
KEYMAP=de
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by hwdetect
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to disable it
#
MODULES=(!usbserial !skge sk98lin snd-via82xx snd-pcm-oss i2c-viapro eeprom k8temp w83627hf)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="myhost"
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
# eth0="eth0 192.168.0.187 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(lo eth0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(main)
#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng !hotplug iptables !pcmcia network dbus hal netfs cups crond nvidia !xdm kdm !slim)
# End of file