dmesg gibt mir immer was aus, also es ist nicht so das er auf irgendwas wartet sondern immer was anzeigt.
Hier mal wenn die Platte an ist.
[ben@penguin ~]$ dmesg
Linux version 2.6.18-ARCH (root@Wohnung) (gcc version 4.1.1) #1 SMP PREEMPT Sat Oct 7 10:30:11 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f4a70
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6500
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff6800
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Detected 1800.160 MHz processor.
Built 1 zonelists. Total pages: 131056
Kernel command line: root=/dev/hda1 rootfs=reiserfs ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 514900k/524224k available (2235k kernel code, 8700k reserved, 700k data, 228k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3603.80 BogoMIPS (lpj=7207604)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 659k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 02
Total of 1 processors activated (3603.80 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb230, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 4080-40bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d8000000-d9ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: da000000-da0fffff
PREFETCH window: da100000-da1fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU0] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 228k freed
Time: tsc clocksource has been installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 18
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD400LB-00DNA0, ATA DISK drive
hdb: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST320420A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: max request size: 128KiB
hdc: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63, UDMA(66)
hdc: cache flushes not supported
hdc: hdc1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 16, io base 0x0000d000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: irq 17, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:02:02.0
-> GSI 16 (level, low) -> IRQ 18
ohci_hcd 0000:02:02.0: OHCI Host Controller
ohci_hcd 0000:02:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:02.0: irq 18, io mem 0xda000000
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usb 1-1.1: new low speed USB device using uhci_hcd and address 3
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1.1: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:02:02.3[A] -> GSI 22 (level, low) -> IRQ 19
ehci_hcd 0000:02:02.3: EHCI Host Controller
ehci_hcd 0000:02:02.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:02:02.3: debug port 1
PCI: cache line size of 128 is not supported by device 0000:02:02.3
ehci_hcd 0000:02:02.3: irq 19, io mem 0xda003000
ehci_hcd 0000:02:02.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:02:02.1[C] -> GSI 18 (level, low) -> IRQ 20
ohci_hcd 0000:02:02.1: OHCI Host Controller
ohci_hcd 0000:02:02.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:02:02.1: irq 20, io mem 0xda001000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-1.3: new full speed USB device using uhci_hcd and address 4
ACPI: PCI Interrupt 0000:02:02.2[D] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:02:02.2: OHCI Host Controller
ohci_hcd 0000:02:02.2: new USB bus registered, assigned bus number 6
ohci_hcd 0000:02:02.2: irq 21, io mem 0xda002000
usb 1-1.3: configuration #1 chosen from 1 choice
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 21 (level, low) -> IRQ 21
eth0: VIA Rhine III at 0x1c800, 00:40:f4:a3:89:39, IRQ 21.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
usbcore: registered new driver hiddev
hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
input: HID 062a:0000 as /class/input/input0
input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1f.2-1.1
input: Generic USB K/B Hub as /class/input/input1
input: USB HID v1.10 Keyboard [Generic USB K/B Hub] on usb-0000:00:1f.2-1.3
input: Generic USB K/B Hub as /class/input/input2
input: USB HID v1.10 Device [Generic USB K/B Hub] on usb-0000:00:1f.2-1.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: replayed 9 transactions in 0 seconds
ReiserFS: hda1: Using r5 hash to sort names
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 18 (level, low) -> IRQ 20
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
agpgart: AGP aperture is 128M @ 0xd0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input3
ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 17 (level, low) -> IRQ 22
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x201, speed 784kHz
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21
Linux video capture interface: v2.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
Real Time Clock Driver v1.12ac
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 20
bttv0: Bt878 (rev 17) at 0000:02:04.0, irq: 20, latency: 32, mmio: 0xda100000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 1-0050: Hauppauge model 61344, rev D421, serial# 3913894
tveeprom 1-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is MSP3415 (idx 6)
tveeprom 1-0050: has radio
bttv0: Hauppauge eeprom indicates model#61344
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
msp3400 1-0040: MSP3415D-B3 supports nicam, mode is autodetect
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 20
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: replayed 2 transactions in 0 seconds
ReiserFS: hda3: Using r5 hash to sort names
ReiserFS: hdc1: found reiserfs format "3.6" with standard journal
ReiserFS: hdc1: using ordered data mode
ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc1: checking transaction log (hdc1)
ReiserFS: hdc1: replayed 1 transactions in 0 seconds
ReiserFS: hdc1: Using r5 hash to sort names
Adding 979956k swap on /dev/hda2. Priority:-1 extents:1 across:979956k
bt878: AUDIO driver version 0.0.0 loaded
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: link down
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
usb 4-5: new high speed USB device using ehci_hcd and address 2
usb 4-5: device not accepting address 2, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 3
usb 4-5: device not accepting address 3, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 4
usb 4-5: device not accepting address 4, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 5
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
process `nslookup' is using obsolete setsockopt SO_BSDCOMPAT
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
usb 4-5: new high speed USB device using ehci_hcd and address 6
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 7
usb 4-5: device not accepting address 7, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 8
usb 4-5: unable to read config index 0 descriptor/start
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 9
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 10
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 11
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 12
usb 4-5: unable to read config index 0 descriptor/all
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 13
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 14
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 15
usb 4-5: unable to read config index 0 descriptor/start
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 16
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 17
usb 4-5: configuration #1 chosen from 1 choice
usb 4-5: can't set config #1, error -71
[ben@penguin ~]$
und hier wenn aus.
[ben@penguin ~]$ dmesg
Linux version 2.6.18-ARCH (root@Wohnung) (gcc version 4.1.1) #1 SMP PREEMPT Sat Oct 7 10:30:11 CEST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
found SMP MP-table at 000f4a70
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126960 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6500
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff6800
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Detected 1800.160 MHz processor.
Built 1 zonelists. Total pages: 131056
Kernel command line: root=/dev/hda1 rootfs=reiserfs ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 514900k/524224k available (2235k kernel code, 8700k reserved, 700k data, 228k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3603.80 BogoMIPS (lpj=7207604)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 659k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: Intel(R) Pentium(R) 4 CPU 1.80GHz stepping 02
Total of 1 processors activated (3603.80 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb230, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 4000-407f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 4080-40bf claimed by ICH4 GPIO
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: d8000000-d9ffffff
PREFETCH window: c0000000-cfffffff
PCI: Bridge: 0000:00:1e.0
IO window: c000-cfff
MEM window: da000000-da0fffff
PREFETCH window: da100000-da1fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 196608 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU0] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 228k freed
Time: tsc clocksource has been installed.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH2: IDE controller at PCI slot 0000:00:1f.1
ICH2: chipset revision 18
ICH2: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: WDC WD400LB-00DNA0, ATA DISK drive
hdb: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST320420A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdc: max request size: 128KiB
hdc: 39851760 sectors (20404 MB) w/2048KiB Cache, CHS=39535/16/63, UDMA(66)
hdc: cache flushes not supported
hdc: hdc1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1f.2[D] -> GSI 19 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
uhci_hcd 0000:00:1f.2: UHCI Host Controller
uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1f.2: irq 16, io base 0x0000d000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1f.4[C] -> GSI 23 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1f.4 to 64
uhci_hcd 0000:00:1f.4: UHCI Host Controller
uhci_hcd 0000:00:1f.4: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1f.4: irq 17, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usb 1-1: new full speed USB device using uhci_hcd and address 2
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:02:02.0 -> GSI 16 (level, low) -> IRQ 18
ohci_hcd 0000:02:02.0: OHCI Host Controller
ohci_hcd 0000:02:02.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:02.0: irq 18, io mem 0xda000000
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 3 ports detected
usb 1-1.1: new low speed USB device using uhci_hcd and address 3
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1.1: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:02:02.3[A] -> GSI 22 (level, low) -> IRQ 19
ehci_hcd 0000:02:02.3: EHCI Host Controller
ehci_hcd 0000:02:02.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:02:02.3: debug port 1
PCI: cache line size of 128 is not supported by device 0000:02:02.3
ehci_hcd 0000:02:02.3: irq 19, io mem 0xda003000
ehci_hcd 0000:02:02.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
ACPI: PCI Interrupt 0000:02:02.1[C] -> GSI 18 (level, low) -> IRQ 20
ohci_hcd 0000:02:02.1: OHCI Host Controller
ohci_hcd 0000:02:02.1: new USB bus registered, assigned bus number 5
ohci_hcd 0000:02:02.1: irq 20, io mem 0xda001000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-1.3: new full speed USB device using uhci_hcd and address 4
ACPI: PCI Interrupt 0000:02:02.2[D] -> GSI 21 (level, low) -> IRQ 21
ohci_hcd 0000:02:02.2: OHCI Host Controller
ohci_hcd 0000:02:02.2: new USB bus registered, assigned bus number 6
ohci_hcd 0000:02:02.2: irq 21, io mem 0xda002000
usb 1-1.3: configuration #1 chosen from 1 choice
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 21 (level, low) -> IRQ 21
eth0: VIA Rhine III at 0x1c800, 00:40:f4:a3:89:39, IRQ 21.
eth0: MII PHY found at address 1, status 0x7869 advertising 05e1 Link 41e1.
usbcore: registered new driver hiddev
hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
input: HID 062a:0000 as /class/input/input0
input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1f.2-1.1
input: Generic USB K/B Hub as /class/input/input1
input: USB HID v1.10 Keyboard [Generic USB K/B Hub] on usb-0000:00:1f.2-1.3
input: Generic USB K/B Hub as /class/input/input2
input: USB HID v1.10 Device [Generic USB K/B Hub] on usb-0000:00:1f.2-1.3
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: replayed 9 transactions in 0 seconds
ReiserFS: hda1: Using r5 hash to sort names
ACPI: PCI Interrupt 0000:02:04.1[A] -> GSI 18 (level, low) -> IRQ 20
ts: Compaq touchscreen protocol output
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel i845 Chipset.
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
agpgart: AGP aperture is 128M @ 0xd0000000
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input3
ACPI: PCI Interrupt 0000:00:1f.3 -> GSI 17 (level, low) -> IRQ 22
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 18
NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-8774 Tue Aug 1 20:54:08 PDT 2006
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x201, speed 784kHz
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21
Linux video capture interface: v2.00
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
Real Time Clock Driver v1.12ac
bttv: Bt8xx card found (0).
ACPI: PCI Interrupt 0000:02:04.0[A] -> GSI 18 (level, low) -> IRQ 20
bttv0: Bt878 (rev 17) at 0000:02:04.0, irq: 20, latency: 32, mmio: 0xda100000
bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
bttv0: using: Hauppauge (bt878) [card=10,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
tveeprom 1-0050: Hauppauge model 61344, rev D421, serial# 3913894
tveeprom 1-0050: tuner model is Philips FM1216 (idx 21, type 5)
tveeprom 1-0050: TV standards PAL(B/G) (eeprom 0x04)
tveeprom 1-0050: audio processor is MSP3415 (idx 6)
tveeprom 1-0050: has radio
bttv0: Hauppauge eeprom indicates model#61344
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... found
msp3400 1-0040: MSP3415D-B3 found @ 0x80 (bt878 #0 [sw])
msp3400 1-0040: MSP3415D-B3 supports nicam, mode is autodetect
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
tuner 1-0061: chip found @ 0xc2 (bt878 #0 [sw])
tuner 1-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 20
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
ReiserFS: hda3: found reiserfs format "3.6" with standard journal
ReiserFS: hda3: using ordered data mode
ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda3: checking transaction log (hda3)
ReiserFS: hda3: replayed 2 transactions in 0 seconds
ReiserFS: hda3: Using r5 hash to sort names
ReiserFS: hdc1: found reiserfs format "3.6" with standard journal
ReiserFS: hdc1: using ordered data mode
ReiserFS: hdc1: journal params: device hdc1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hdc1: checking transaction log (hdc1)
ReiserFS: hdc1: replayed 1 transactions in 0 seconds
ReiserFS: hdc1: Using r5 hash to sort names
Adding 979956k swap on /dev/hda2. Priority:-1 extents:1 across:979956k
bt878: AUDIO driver version 0.0.0 loaded
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: no IPv6 routers present
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
eth0: link down
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
usb 4-5: new high speed USB device using ehci_hcd and address 2
usb 4-5: device not accepting address 2, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 3
usb 4-5: device not accepting address 3, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 4
usb 4-5: device not accepting address 4, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 5
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
process `nslookup' is using obsolete setsockopt SO_BSDCOMPAT
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
cdrom: This disc doesn't have any tracks I recognize!
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
usb 4-5: new high speed USB device using ehci_hcd and address 6
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 7
usb 4-5: device not accepting address 7, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 8
usb 4-5: unable to read config index 0 descriptor/start
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 9
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 10
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 11
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 12
usb 4-5: unable to read config index 0 descriptor/all
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 13
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 14
usb 4-5: device descriptor read/all, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 15
usb 4-5: unable to read config index 0 descriptor/start
usb 4-5: can't read configurations, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 16
usb 4-5: device descriptor read/8, error -71
usb 4-5: device descriptor read/8, error -71
usb 4-5: new high speed USB device using ehci_hcd and address 17
usb 4-5: configuration #1 chosen from 1 choice
usb 4-5: can't set config #1, error -71
usb 4-5: USB disconnect, address 17
[ben@penguin ~]$