Danke, den Treiber habe ich jetzt erstellt und mit modprobe eingebunden.
Ein 'lsmod | grep rtl' zeigt:
rtl8723de 102400 0
btrtl 16384 1 btusb
phydm_mod 917504 1 rtl8723de
bluetooth 634880 5 btrtl,btintel,btbcm,btusb
btcoexist 479232 1 rtl8723de
rtl8723_common 28672 1 rtl8723de
rtl_pci 36864 1 rtl8723de
rtlwifi 176128 5 phydm_mod,rtl_pci,btcoexist,rtl8723_common,rtl8723de
mac80211 905216 2 rtl_pci,rtlwifi
cfg80211 749568 2 mac80211,rtlwifi
'ip link' sieht so aus:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether ac:e2:d3:17:34:77 brd ff:ff:ff:ff:ff:ff
3: wlo1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether 40:9f:38:d7:e8:01 brd ff:ff:ff:ff:ff:ff
Also habe ich netctl konfiguriert. Wenn ich jetzt 'netctl start wlo1' eingebe bekomm ich die Fehlermeldung
Job for netctl@wlo1.service failed because the control process exited with error code.
'systemctl status
netctl@wlo1.service' meldet dann
● netctl@wlo1.service - Networking for netctl profile wlo1
Loaded: loaded (/usr/lib/systemd/system/netctl@.service; static; vendor preset: disabled)
Active: failed (Result: exit-code) since Thu 2018-04-26 21:53:11 CEST; 3min 52s ago
Docs: man:netctl.profile(5)
Process: 699 ExecStart=/usr/lib/netctl/network start wlo1 (code=exited, status=1/FAILURE)
Main PID: 699 (code=exited, status=1/FAILURE)
Apr 26 21:53:11 archbook systemd[1]: Starting Networking for netctl profile wlo1...
Apr 26 21:53:11 archbook network[699]: Profile 'wlo1' does not exist or is not readable
Apr 26 21:53:11 archbook systemd[1]: netctl@wlo1.service: Main process exited, code=exited, status=1/FAILURE
Apr 26 21:53:11 archbook systemd[1]: netctl@wlo1.service: Failed with result 'exit-code'.
Apr 26 21:53:11 archbook systemd[1]: Failed to start Networking for netctl profile wlo1.
Auch ein 'ip link set wlo1 up' ändert nichts, ebenso wie ein beherztes 'rfkill unblock wlan'.
Dabei hatte ich damit schon ein Authentifizierungsproblem. Also wird doch das Dingen irgendwie erreichbar sein oder?
Nachtrag:
Die Ausgabe von 'rfkill list':
0: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
1: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
und von 'iwconfig':
wlo1 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Power Management:off