Hallo,
das hat es leider auch nicht gebracht, ebenso der neue Kernel von heute.
Jul 8 05:48:36 mypc kernel: e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
Jul 8 05:48:36 mypc kernel: e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: setting latency timer to 64
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: Disabling ASPM L0s
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:38 mypc kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
Mit dem Treiber von der Intel-Homepage steht da
Jul 8 05:39:37 mypc kernel: e1000e 0000:02:00.0: ASPM disabled system-wide
Mit dem 2.6.33er Kernel hatte ich allerdings
Jul 7 05:38:28 mypc kernel: e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
Jul 7 05:38:28 mypc kernel: e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: Disabling L1 ASPM
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: setting latency timer to 64
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: Warning: detected ASPM enabled in EEPROM
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 7 05:38:28 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 7 05:38:30 mypc kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
Also scheint das L1 das Problem zu sein - ich muß mal schauen, ob ich irgendwo rausfinde, wie man das Disabled. Die Option SmartPowerDownEnable scheint es wohl nicht zu tun (obwohl ich das nicht so richtig verifizieren kann).
Edit: Irgendwie läuft es jetzt grade flüssig...ich hab so das Gefühl, daß das Mistding mich hier verarschen will...L1 ist aber enabled
02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller
Subsystem: Lenovo ThinkPad T60
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 30
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 3000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0300c Data: 41c9
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM L1 Enabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP+ BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
Capabilities: [140 v1] Device Serial Number 00-16-41-ff-ff-aa-4b-dc
Kernel driver in use: e1000e
Kernel modules: e1000e
Auf dem Interface war seit dem letzten Reboot auch keine Änderung. Zumindest steht nichts im everything.log:
Jul 8 05:48:36 mypc kernel: e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
Jul 8 05:48:36 mypc kernel: e1000e: Copyright (c) 1999 - 2009 Intel Corporation.
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: setting latency timer to 64
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: Disabling ASPM L0s
Jul 8 05:48:36 mypc kernel: 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:16:41:aa:4b:dc
Jul 8 05:48:36 mypc kernel: 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection
Jul 8 05:48:36 mypc kernel: 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005301-003
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:36 mypc kernel: e1000e 0000:02:00.0: irq 30 for MSI/MSI-X
Jul 8 05:48:36 mypc dhcpcd[1672]: eth0: waiting for carrier
Jul 8 05:48:38 mypc kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
Jul 8 05:48:38 mypc kernel: 0000:02:00.0: eth0: 10/100 speed: disabling TSO
Jul 8 05:48:38 mypc dhcpcd[1672]: eth0: carrier acquired
Jul 8 05:48:38 mypc dhcpcd[1672]: eth0: rebinding lease of 192.168.0.115
Jul 8 05:48:38 mypc dhcpcd[1672]: eth0: acknowledged 192.168.0.115 from 192.168.0.1
Jul 8 05:48:38 mypc dhcpcd[1672]: eth0: checking for 192.168.0.115
Jul 8 05:48:43 mypc dhcpcd[1672]: eth0: leased 192.168.0.115 for 1296000 seconds
Wie man sehen kann, ist es wieder der Kerneltreiber von Arch, der mit dem Update heute kam. Nach dem Boot war es aber eine geraume Zeit extrem langsam.