Hallo,
seit geraumer Zeit habe ich mit meinem Archlinux ein Festplattenproblem. Wie lange kann ich nicht genau sagen, ich bin wenn nichts mehr lief auf ein ebenfalls auf der Maschine eingerichtetes Gentoo-System ausgewichen.
Wenn ich meinen Rechner gebootet habe, fällt nach kurzer Zeit die Festplatte aus, weiter arbeiten ist dann unmöglich, nicht mal normales Herunterfahren per shutdown -h now, neu starten ist nur per Reset Knopf möglich, aber Zwecklos, das dann die SATA-Festplatte vom BIOS nicht mehr erkannt wird. Die ist erst wieder verfügbar, wenn der Rechner ausgeschaltet wurde.
Auf meinem Rechner läuft Archlinux mit aktuellem x86_64 Kernel (derzeit 2.6.32).
Meine Hardware besteht aus:
Biostar-Mainboard mit AMD 790GX Chipsatz,
Nvidia geForce 8400GS Grafikkarte (onboard Grafik ist deaktiviert),
Phenom X4 9950 Prozessor,
Festplatten sind:
Western Digital WDC WD6400AAKS-00A7B0 (an SATA, mit dieser Platte tritt das Problem auf)
Samsung SAMSUNG HD400LD, WQ100-14 (an IDE).
Im BIOS sind beide (IDE- und SATA-Controller aktiviert, SATA-Modus ist "AHCI")
dmesg liefert:
[...]
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2065241
Kernel command line: root=/dev/disk/by-uuid/d428cded-fae7-4359-bed1-ca2c5d0f1576 resume=/dev/disk/by-uuid/b34954a3-936a-41b0-bcc4-1c15edeb2be8 ro vga=795
[...]
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:08: ioport range 0xe00-0xe0f has been reserved
system 00:08: ioport range 0xe80-0xe8f has been reserved
system 00:08: ioport range 0xf40-0xf4f has been reserved
system 00:08: ioport range 0xa30-0xa3f has been reserved
system 00:0a: iomem range 0xfec00000-0xfec00fff could not be reserved
system 00:0a: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
system 00:0b: ioport range 0x40b-0x40b has been reserved
system 00:0b: ioport range 0x4d6-0x4d6 has been reserved
system 00:0b: ioport range 0xc00-0xc01 has been reserved
system 00:0b: ioport range 0xc14-0xc14 has been reserved
system 00:0b: ioport range 0xc50-0xc51 has been reserved
system 00:0b: ioport range 0xc52-0xc52 has been reserved
system 00:0b: ioport range 0xc6c-0xc6c has been reserved
system 00:0b: ioport range 0xc6f-0xc6f has been reserved
system 00:0b: ioport range 0xcd0-0xcd1 has been reserved
system 00:0b: ioport range 0xcd2-0xcd3 has been reserved
system 00:0b: ioport range 0xcd4-0xcd5 has been reserved
system 00:0b: ioport range 0xcd6-0xcd7 has been reserved
system 00:0b: ioport range 0xcd8-0xcdf has been reserved
system 00:0b: ioport range 0x800-0x89f has been reserved
system 00:0b: ioport range 0xb00-0xb0f has been reserved
system 00:0b: ioport range 0xb20-0xb3f has been reserved
system 00:0b: ioport range 0x900-0x90f has been reserved
system 00:0b: ioport range 0x910-0x91f has been reserved
system 00:0b: ioport range 0xfe00-0xfefe has been reserved
system 00:0b: iomem range 0xffb80000-0xffbfffff has been reserved
system 00:0b: iomem range 0xfec10000-0xfec1001f has been reserved
system 00:0b: iomem range 0xcff00000-0xcfffffff could not be reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0xcfefffff could not be reserved
system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved
pci 0000:00:02.0: PCI bridge, secondary bus 0000:01
pci 0000:00:02.0: IO window: 0xd000-0xdfff
pci 0000:00:02.0: MEM window: 0xfa000000-0xfe9fffff
pci 0000:00:02.0: PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:07.0: PCI bridge, secondary bus 0000:02
pci 0000:00:07.0: IO window: 0xe000-0xefff
pci 0000:00:07.0: MEM window: 0xfea00000-0xfeafffff
pci 0000:00:07.0: PREFETCH window: 0x000000f8f00000-0x000000f8ffffff
pci 0000:00:14.4: PCI bridge, secondary bus 0000:03
pci 0000:00:14.4: IO window: disabled
pci 0000:00:14.4: MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:14.4: PREFETCH window: disabled
pci 0000:00:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
pci 0000:00:02.0: setting latency timer to 64
pci 0000:00:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
pci 0000:00:07.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfa000000-0xfe9fffff]
pci_bus 0000:01: resource 2 pref mem [0xd0000000-0xdfffffff]
pci_bus 0000:02: resource 0 io: [0xe000-0xefff]
pci_bus 0000:02: resource 1 mem: [0xfea00000-0xfeafffff]
pci_bus 0000:02: resource 2 pref mem [0xf8f00000-0xf8ffffff]
pci_bus 0000:03: resource 1 mem: [0xfeb00000-0xfebfffff]
pci_bus 0000:03: resource 3 io: [0x00-0xffff]
pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffffffffffff]
[...]
libata version 3.00 loaded.
pata_acpi 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pata_acpi 0000:00:14.1: setting latency timer to 64
scsi0 : pata_atiixp
scsi1 : pata_atiixp
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
ata2.00: ATA-7: SAMSUNG HD400LD, WQ100-14, max UDMA/100
ata2.00: 781422768 sectors, multi 16: LBA48
ata2.00: configured for UDMA/100
scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD400LD WQ10 PQ: 0 ANSI: 5
ahci 0000:00:11.0: version 3.0
ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:11.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc
scsi2 : ahci
scsi3 : ahci
scsi4 : ahci
scsi5 : ahci
sd 1:0:0:0: [sda] 781422768 512-byte logical blocks: (400 GB/372 GiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1
ata3: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff900 irq 22
sd 1:0:0:0: [sda] Attached SCSI disk
ata4: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fff980 irq 22
ata5: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa00 irq 22
ata6: SATA max UDMA/133 abar m1024@0xf9fff800 port 0xf9fffa80 irq 22
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata5: softreset failed (device not ready)
ata4: softreset failed (device not ready)
ata4: applying SB600 PMP SRST workaround and retrying
ata5: applying SB600 PMP SRST workaround and retrying
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-8: WDC WD6400AAKS-00A7B0, 01.03B01, max UDMA/133
ata4.00: 1250263728 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4.00: configured for UDMA/133
ata5.00: ATAPI: HL-DT-ST DVDRAM GH20NS15, IL00, max UDMA/100
ata5.00: configured for UDMA/100
scsi 3:0:0:0: Direct-Access ATA WDC WD6400AAKS-0 01.0 PQ: 0 ANSI: 5
sd 3:0:0:0: [sdb] 1250263728 512-byte logical blocks: (640 GB/596 GiB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
scsi 4:0:0:0: CD-ROM HL-DT-ST DVDRAM GH20NS15 IL00 PQ: 0 ANSI: 5
sdb: sdb1 sdb2 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 >
sd 3:0:0:0: [sdb] Attached SCSI disk
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 4:0:0:0: Attached scsi CD-ROM sr0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:12.2: EHCI Host Controller
ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:12.2: applying AMD SB600/SB700 USB freeze workaround
ehci_hcd 0000:00:12.2: debug port 1
ehci_hcd 0000:00:12.2: irq 17, io mem 0xf9fff000
ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:13.2: EHCI Host Controller
ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:13.2: applying AMD SB600/SB700 USB freeze workaround
ehci_hcd 0000:00:13.2: debug port 1
ehci_hcd 0000:00:13.2: irq 19, io mem 0xf9ff6800
ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.0: OHCI Host Controller
ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:12.0: irq 16, io mem 0xf9ffe000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:12.1: OHCI Host Controller
ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:12.1: irq 16, io mem 0xf9ffd000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.0: irq 18, io mem 0xf9ffc000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 3 ports detected
ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.1: irq 18, io mem 0xf9ff7000
usb 1-4: new high speed USB device using ehci_hcd and address 3
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 3 ports detected
ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
ohci_hcd 0000:00:14.5: OHCI Host Controller
ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
ohci_hcd 0000:00:14.5: irq 18, io mem 0xf9ff5000
usb 1-4: configuration #1 chosen from 1 choice
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-6: new high speed USB device using ehci_hcd and address 4
PM: Starting manual resume from disk
PM: Resume from partition 8:25
PM: Checking hibernation image.
PM: Error -22 checking image file
PM: Resume from disk failed.
PM: Starting manual resume from disk
PM: Resume from partition 8:25
PM: Checking hibernation image.
PM: Error -22 checking image file
PM: Resume from disk failed.
usb 1-6: configuration #1 chosen from 1 choice
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with writeback data mode.
usb 3-3: new full speed USB device using ohci_hcd and address 2
ata4.00: exception Emask 0x50 SAct 0x2 SErr 0x280900 action 0x6 frozen
ata4.00: irq_stat 0x08000000, interface fatal error
ata4: SError: { UnrecovData HostInt 10B8B BadCRC }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/f8:08:fc:98:05/00:00:18:00:00/40 tag 1 ncq 126976 in
res 40/00:0c:fc:98:05/00:00:18:00:00/40 Emask 0x50 (ATA bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
usb 3-3: configuration #1 chosen from 1 choice
ata4: softreset failed (device not ready)
ata4: applying SB600 PMP SRST workaround and retrying
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
udev: starting version 151
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:02:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
r8169 0000:02:00.0: setting latency timer to 64
r8169 0000:02:00.0: irq 27 for MSI/MSI-X
eth0: RTL8168c/8111c at 0xffffc900100a2000, 00:e0:4d:8a:bb:db, XID 1c4000c0 IRQ 27
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 3:0:0:0: Attached scsi generic sg1 type 0
sr 4:0:0:0: Attached scsi generic sg2 type 5
ACPI: I/O resource piix4_smbus [0xb00-0xb07] conflicts with ACPI region SOR1 [0xb00-0xb0f]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
logips2pp: Detected unknown logitech mouse model 127
ata4.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata4.00: irq_stat 0x08000000, interface fatal error
ata4: SError: { UnrecovData HostInt 10B8B BadCRC }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:00:44:f9:03/01:00:18:00:00/40 tag 0 ncq 131072 in
res 40/00:04:44:f9:03/00:00:18:00:00/40 Emask 0x50 (ATA bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input2
ata4: softreset failed (device not ready)
ata4: applying SB600 PMP SRST workaround and retrying
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
cfg80211: Calling CRDA to update world regulatory domain
processor LNXCPU:00: registered as cooling_device0
processor LNXCPU:01: registered as cooling_device1
processor LNXCPU:02: registered as cooling_device2
processor LNXCPU:03: registered as cooling_device3
input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3
ACPI: Power Button [PWRB]
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
ACPI: Power Button [PWRF]
usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0182
usbcore: registered new interface driver usblp
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (31 C)
EDAC MC: Ver: 2.1.0 Feb 9 2010
EDAC amd64_edac: Ver: 3.2.0 Feb 9 2010
EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3).
EDAC amd64: WARNING: ECC is disabled by BIOS. Module will NOT be loaded.
Either Enable ECC in the BIOS, or set 'ecc_enable_override'.
Also, use of the override can cause unknown side effects.
amd64_edac: probe of 0000:00:18.2 failed with error -22
HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
scsi 6:0:0:0: Direct-Access WD 1000FYP External 1.75 PQ: 0 ANSI: 4
sd 6:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
sd 6:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
sd 6:0:0:0: [sdc] Write Protect is off
sd 6:0:0:0: [sdc] Mode Sense: 23 00 00 00
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 6:0:0:0: [sdc] Assuming drive cache: write through
sd 6:0:0:0: [sdc] Attached SCSI disk
nvidia 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 190.53 Wed Dec 9 15:29:46 PST 2009
scsi 7:0:0:0: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
sd 7:0:0:0: Attached scsi generic sg4 type 0
scsi 7:0:0:1: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
sd 7:0:0:1: Attached scsi generic sg5 type 0
sd 7:0:0:0: [sdd] Attached SCSI removable disk
scsi 7:0:0:2: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
sd 7:0:0:2: Attached scsi generic sg6 type 0
scsi 7:0:0:3: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
sd 7:0:0:3: Attached scsi generic sg7 type 0
sd 7:0:0:1: [sde] Attached SCSI removable disk
sd 7:0:0:3: [sdg] Attached SCSI removable disk
sd 7:0:0:2: [sdf] Attached SCSI removable disk
usb-storage: device scan complete
hda_codec: ALC888: BIOS auto-probing.
input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:14.2/input/input5
ath9k 0000:03:06.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
powernow-k8: Found 1 AMD Phenom(tm) 9950 Quad-Core Processor processors (4 cpu cores) (version 2.20.00)
powernow-k8: 0 : pstate 0 (2600 MHz)
powernow-k8: 1 : pstate 1 (1300 MHz)
fuse init (API version 7.13)
ath: EEPROM regdomain: 0x30
ath: EEPROM indicates we should expect a direct regpair map
ath: Country alpha2 being used: AM
ath: Regpair used: 0x30
phy0: Selected rate control algorithm 'ath9k_rate_control'
cfg80211: Calling CRDA for country: AM
Registered led device: ath9k-phy0::radio
Registered led device: ath9k-phy0::assoc
Registered led device: ath9k-phy0::tx
Registered led device: ath9k-phy0::rx
phy0: Atheros AR5416 MAC/BB Rev:2 AR2133 RF Rev:81: mem=0xffffc90010c40000, irq=21
EXT3 FS on sdb7, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb6, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb8, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
it87: Found IT8718F chip at 0xe80, revision 5
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
ACPI: I/O resource it87 [0xe85-0xe86] conflicts with ACPI region SENP [0xe85-0xe86]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
r8169: eth0: link up
r8169: eth0: link up
ata4.00: exception Emask 0x0 SAct 0x7 SErr 0x80000 action 0x6
ata4.00: irq_stat 0x40000008
ata4: SError: { 10B8B }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/00:00:3c:64:3c/01:00:14:00:00/40 tag 0 ncq 131072 in
res 41/84:bf:7d:64:3c/00:00:14:00:00/40 Emask 0x410 (ATA bus error) <F>
ata4.00: status: { DRDY ERR }
ata4.00: error: { ICRC ABRT }
ata4: hard resetting link
ata4: softreset failed (device not ready)
ata4: applying SB600 PMP SRST workaround and retrying
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: configured for UDMA/133
ata4: EH complete
ata4: limiting SATA link speed to 1.5 Gbps
ata4.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen
ata4.00: irq_stat 0x08000000, interface fatal error
ata4: SError: { UnrecovData HostInt 10B8B BadCRC }
ata4.00: failed command: READ FPDMA QUEUED
ata4.00: cmd 60/e0:00:c4:45:8f/00:00:17:00:00/40 tag 0 ncq 114688 in
res 40/00:04:c4:45:8f/00:00:17:00:00/40 Emask 0x50 (ATA bus error)
ata4.00: status: { DRDY }
ata4: hard resetting link
ata4: softreset failed (device not ready)
ata4: applying SB600 PMP SRST workaround and retrying
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4.00: configured for UDMA/133
ata4: EH complete
Kennt jemand dieses Problem und hat einen Tipp für mich? Von einem Hardwaredefekt gehe ich nicht aus, da andere Partitionen einwandfrei funktionieren.
Grüße aus Koblenz,
Ansgar